Install a New Filter Cartridge per Manufacturers Instructions. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Clean or replace the spa filter, open all the jets and turn the pump on high. If your spa is equipped with a circulating pump, there is a screen-like fitting in your hot tub that bubbles and/or hot water comes out of. this contact form
How to easily fix Fl Error Viking Spa error? Heat Related Pump Not Running.8. SE = Spa operating in Standard-in-Economy Mode. Wondering what your spa is trying to tell you? news
If you do not see water flowing from the circ pump outlet, IMMEDIATELY turn off power to the spa (as an attempt at heating will occur within a minute of the Hayward S166T Pool... Thank you for a great post, it fixed mine as well! After the water cools, a high limit switch may be need to be reset on some spa packs; look for a red reset button.
LF = Persistent low flow problems. (Displays on the 5th occurrence of "HFL" message with 24 hours). Press "Mode" Button to Clear Message. drops. Marquis Spa Error Codes August 28, 2015 at 5:23 PM Lucky923 said...
Rinsing the filters with just water isn't going to do it.Have you just refilled your spa? Balboa Hot Tub Error Codes When water doesn't flow fast enough through the heater, it removes less heat, and the temperature of the water increases. Proceed step by step, and you should be able to find the cause of the FL, FLO or FLOW error code. http://vikingspas.com/why-viking/downloads The System will stay in the Standard Mode for 1 Hour unless the "Mode/Prog" Button is Pressed on a Panel with a "Mode/Prog" Button, or the "Temp" Followed by "Light" Buttons
If there is No Error Message, Select "No Error Message" Below. Hot Tub Error Code Oh Heater is deactivated. All Rights Reserved. Blocked Skimmer.4.
The Heater and Pump will Operate Any time the Thermostat Demands Heat. Ecn = Spa operating in Economy Mode. Hot Tub Error Codes leaves, scumballs, etc. How To Fix Flo Error Hot Tub Here's what to do if your spa throws a FL, FLO or FLOW error code at you.
If so just add water to the spa and that should fix it. http://interskillmedia.com/error-code/fix-error-799.html Here's another Cal Spa troubleshooting flowchart for spa error codes OH, including testing the spa heater element for excessive resistance, done with the spa heater and all systems powered Off, and Back to Top SAL or SANITIZER LOW Message At the ORP Sensor, the "Sanitizer Level is Low" (SAL).With an ORP Sensor Installed in the System, the Sanitizer Level is Below 740 Back to Top rCO or CLEAN COVER Message Time to Clean "Cover Reminder" (rCO).Appears Every 180 Days*. Vita Spa Error Codes
they may have 2 plastic "flags" that protect some wire connectors. Too Many Closed Jets.6. Back to Top PHL or PH IS LOW RAISE PH Message At the pH Sensor, the "pH Level is Low" (PHL).With a pH Sensor Installed in the System, the pH Level navigate here Blocked Suction Fitting.3.
At the same time this test is being done, put your hand on the stainless steel heater manifold, it should NOT be hot, it should only be at the same temperature Great Lakes Hot Tub Error Codes FL could be a code for low flow. All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 180 Days, but some Spa Brands or Models may be Different.
The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles. Turn the breaker to the spa OFF, and then cycle it back ON. You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. Hydropool Hot Tub Error Codes If water is flowing from the circ pump outlet, proceed to test all the other pumps.If the Circ Pump is primed, or if you Do Not have a Circ Pump, then:-
Consumer Reviews EasyPak Spa Controls "Very pleased with the ease of installation and all the diagnostic features that other spa packs did not even have. If all of this check out OK there is always the possibility that you have a defective pressure switch which is mounted somewhere on the heater tube. Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". his comment is here Noisy pump but tub working ok until after water change.
Therefore, "OHH" is considered to be a Flow Related Error.Check for All of the following Conditions:1. Back to Top Ecn or Ec Message Ecn or Ec MessageIf the Ecn or Ec Message is Alternating with the Water Temperature on the Display, the Spa is Operating in the Blocked Suction Fitting.3. Heat Related Pump Not Primed.9.
This website should be used for informational purposes only. Question about Dream Series Dream Master Hot Tub with Flex Cover 1 Answer Where can i view a leisure bayhot tub manual? ...a copy of the Leisure Bay hot tub owners If you have any other questions or problems, please call us at 734-668-7665. Back to Top DETAILED PRIMING INSTRUCTIONS In Priming Mode, Nothing turns on Automatically*.*Note: On the VS/GS Model, the Circ Pump will be on, and on some EL/GL Models, a continuous filtration
Some older spas, and even some new ones have pressure switches. PDF Manual Manual50.pdf. If a continuously running low-speed-only pump is only used for filtering (not for heating), that is not called a circ pump, but instead may be referred to as a "continuous filtration basic features: (repairs system freezing and rebooting issues , start-up customization , browser helper object management , program removal management , live updates , windows structure repair.) Recommended Solution Links: (1)
Back to Top rPH or CHECK PH Message Time to Check "pH Level Reminder" (rPH).Appears Every 7 Days*. Add pH Decreaser according to Manufacturers Instructions.Note: If you do Not have a pH Sensor installed in the Spa System, you should Never get this Message. Leisure Bay Spas Hot Tubs ... OHH = Overheat.
Back to Top dr or HEATER MAY BE DRY WILL RETEST SHORTLY Message There is Possibly a "Dry" (dr) Heater.