navigation
Hot Tubs

What we want to do is take and turn this up to one turn clockwise, slowly until that error code goes away.

I have the temp set at 99. Balboa Hot Tub Error Codes This sometimes refreshes the pc board software if there is anything funky going on. Search Hot Tubs Arctic Spas Arctic Fox Arctic Cub Arctic Yukon Arctic Glacier Arctic Glacier XL Arctic Frontier Arctic Klondiker Arctic Summit Arctic Tundra Arctic Norwegian Arctic Summit XL Arctic Kodiak Flow switch open, flow switch closed.

Where Is The Flow Switch On A Hot Tub

The PWA is the circuit board. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-fl-flo-flow-lf/ I checked to make sure no cut valves were closed. Hot Tub Error Codes Bob Bob Oltman October 21, 2011 at 9:22 am Ok there is the small circ pump. Hydropool Hot Tub Error Codes If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter.

Any ideas?? this content First determine which message you are seeing. Or do I need to flip the breaker to get it back to normal? Is the PWA the circuit board? Vita Spa Error Codes

If you're in the Philadelphia, PA region (including New Jersey) our service department specializes in Hot Spring, Caldera & Sundance Spa repairs & we're authorized to service a few other brands, Today, I want to talk about two error codes that we get on the top site display. NOTE: The Hi Limit Sensor is located behind a shield on the stainless heater manifold and is the smaller of the two silver bullets. weblink If all these test are checked and they did not solve the error code issues, then it is possible you have a defective hi limit sensor.

IF all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance Spa. Flc Error Code On Hot Tub We make no representation as to the accuracy or completeness of this data and are not responsible for errors or omissions. We carry the top selling brands Hot Spring Portable Spas and Caldera Spas Like us on Facebook Post Categories Post Categories Select Category ACE Monthly Tip ACE Salt water generator ACE

COOL = Spa water is more than 20° F cooler than the temperature set point.

Step 2. See M7 Sensors here. The circ jets are pushing out luke warm water to maintain the 89. Hot Tub Flow Switch Troubleshooting Nigel May 21, 2016 Reply Sean you could have an airlock that needs to be purged.

It wants to - I keep hearing ‘clicking' as if something's trying to engage - but all that happens is that the temp indicator keeps rising to the point that the All Rights Reserved. The light did come on above the heat sign but the flo error was still there. check over here With a complete retail pool store in Amesbury.

© 2014 Precision Pool Construction | 978-388-2585 | [emailprotected] Back to Top Optimization WordPress Plugins & Solutions by W3 EDGE

Snb = Spa is shut down. Once I hooked the topside control panel back in, nothing displayed in the red led screen. Also try it this way, Unplug the wires from the pressure switch/flow switch, turn on the pump and then jump the wires. When water isn't flowing fast enough through the heater, the FLO error code shuts things down, to avoid a total meltdown (well, not really a melt-down, but you know).

I bled it, and tried the pump and it seems to circulate the water, but will not cycle properly. Step 1. admin November 2, 2015 at 9:38 am Hi Jennie, I am not rally familiar with the Spa in the Box style tubs, however if you are not getting the right amount That will take care of the problem for you.

This goes away sometimes and I get a solid temp reading. which means flow switch open because the contacts have not closed. Problem 2 LF low flow at certain times with no heat, and a dry warning, not sure what that means, but doesn't sound good.