Solution: Insert a disk into the floppy drive. I then checked the system event log on the bottom. Turn the computer on. I've been checking the most forums and others say that my Hard Disk is broken Can't believe that cause my PC is still reading it and I tried 3 other Hard weblink
Updating didn't generate any change, but I'm wondering whether "un-installing" (then re-installing again) the driver will have any effect on the error message at "Startup." 2. The quad density came in two variations only, single sided (8050 DOS2.5/2.7) and double sided (8250/1001 DOS2.7). The pins on the MOB are enclosed so you can't get them shifted, so are the ones on the drive itself. Report doeboy- Oct 6, 2009 06:22PM went through the bios and didnt c anything that said , standard cmos, im pretty good with pcs and iv seen that b4 but I
The drive should be replaced. If they are, I would try using another FDD power connection from the PSU, and then replace the floppy data ribbon - be sure the red stripe is aligned with pin Arrow down to select "Integrated peripherals" - press enter; Arrow down to select "Onboard FDC controller" - press enter; Arrow cursor to select "disabled" - press enter; Press F10 to save
It took care of my "diskette drive 0 seek failure" problem. The disk in drive A is not formatted. I solved the problem. The Disk Media Is Not Recognized Floppy I go it up and going and installed service pack 3, all seems to be good except for the initial black screen.
Thanks alot Report mnm- Mar 31, 2010 01:09AM works fine. Floppy Disk Drive Problems You do have the 'E' drive, right? If the floppy drive is not setup properly you may experience read/write errors or the floppy may not work at all. Pete http://pski.net Reply With Quote August 24th, 2016,04:35 PM #8 inotarobot View Profile View Forum Posts Private Message View Blog Entries View Articles Senior Member Join Date Feb 2014 Location Melbourne,
If the problem persists, replace the diskette/CD-drive subsystem. Floppy Disk Driver Windows 7 When the Windows desktop appears, click Start, Programs, and Windows Explorer. Note how it is oriented and firmly pull the cable straight off and push it back on the same way that you took it off. In Setup, press F5 on the keyboard to load defaults.
But what are the odds 4 out of 4 drives failed? http://www.techrepublic.com/forums/discussions/floppy-drive-failed-40-error-on-startup/ I do not know much about IT. Floppy Disk Problems And Solutions Like all the other codes out there. How To Read A Floppy Disk Without Formatting It Here's the meaning from the 8050/8250 service manual: POWER UP DIAGNOSTIC FOR 8050/8250 FLASH CODE On power up, the three LED's on the drive should blink.
Generated Thu, 24 Nov 2016 00:27:53 GMT by s_mf18 (squid/3.5.20) Home· Forums· About Us· Awards· Contact Us· Upgrade your BIOS BIOS UPDATES Click to scan for Bios Updates BIOS PostCodes Acer have a peek at these guys Close all windows and restart the computer Follow any on-screen instructions that appear. Thank you. All rights reserved. Floppy Disk Format Error
Skip to Main Content Search Help Tips Dictionary History Forums Contact You are here: Help > Hardware Help > Floppy Drive Help Basic floppy disk drive troubleshooting Note: This document is Floppy Disk Not Recognized Also check on the Motherboard to see if you have pin 1 on pin 1 if the connector is free standing. :) 0Votes Share Flag Collapse - Must not be the I already tried f12 after turning on.
You do have the 'E' drive, right? Here's a copy of the manual I'm using: https://dl.dropboxusercontent.com/u/...anual_1983.pdf That grunt on start, sounds like my better half when she gets worken up by one of our inconsiderate neighbour's starting a The single sided drives could even read the double sided disks, as long as the second side was not used. Floppy Disk Not Accessible Report scott- Feb 26, 2010 02:49PM Hey my service tag for dell is 22jm0(zero)51 just tellin you that to know the type of pc I have..
Recently added New Hardware?If you have such as a tape backup unit, sound card, scanner, network card, etc. Any other ideas are welcome! 0Votes Share Flag Collapse - Follow these steps by Jacky Howe · 8 years ago In reply to All of the above ? :( It could Step 1: Try a different floppy disk This is a simple yet often overlooked step that can save you a lot of time and effort. http://interskillmedia.com/floppy-disk/floppy-drive-repair.html I should also add that it makes a 1 second grunting noise at startup too.
I had several used floppy drives that I tried it with and one of them was new. I followed your advice and it worked. You can read more about this here. Disk drive error codesThe Commodore disk drives indicated hardware failures detected during boot with a blink code. Report salamat- Nov 28, 2009 02:55PM how will I do that??
Can't find your answer ?